|
710
JETSET PRIMER
740 JET SET FLOOR
|
 |
` |
|
Jet
Set repair of pickle tanks.
(click to enlarge) |
DESCRIPTION
710 JET SET PRIMER is used as the prime coat for
all of the JET SET coating systems. It can also be used
as an inexpensive, hard, chemical resistant seal coat
for new or old concrete floors.
MAJOR ADVANTAGES
- 100% solids.
- Exceptional
chemical & abrasion resistance.
- Completely
seals the pores of new or old concrete.
- Rapid cure.
- Low
temperature applications.
- Agriculture
Canada approved for incidental food contact.
|
 |
|
Jet
Set repair of pickle tanks at Stelco Hilton
Works, Hamilton, Ontario. |
TECHNICAL DATA
| Cure
Time |
Initial
Set & recoat |
30-45
mins |
| |
Light
traffic |
2-4
hours |
| |
Full
service |
4-8
hours |
| Net weight |
1
kg/L |
| Flash Point |
31°C |
| Solids
by volume |
100% |
| Application
temperature |
sub-zero
to 30°C |
| |
Normal
formulation |
6
to 30°C |
| |
Freezer formulation |
-30
to 5°C |
| Temperature
resistances |
up
to 120°C |
| Hardness |
Shore
D |
87 |
| Abrasion resistance - Weight
Loss |
with
C-10 wheels |
No
loss |
| |
with
H-22 ceramic wheels |
0.5
gm |
| Weatheromether
500 hrs. |
No
change |
| Water
absorption |
0.74% |
| Resistance
to Chloride penetration |
Excellent |
PRODUCT INFORMATION
| Number of components |
Two, Base resin & catalyst |
| Packaging |
4L and 20L |
| Coverage |
12m3 (125 sq.ft./L) |
| Primer |
Non-required |
| Thinner |
NEVER add thinners. 100% solids material |
| Clean-up |
Styrene or acetone to clean equipment |
| Pot life |
Less than 15 mins if both components are mixes.
Remove from pot and rough spread immediately or use
two component spray equipment. |
| Colours |
Clear |
| Finish |
Semi-gloss |
| Shelf life |
6 months at 5 to 24°C inside storage out of sun and
away from direct heat. |
All testing to ASTM Standards by
Independent Laboratories.
|
|
724 JET SET FLOOR
710 JET SET PRIMER
DESCRIPTION
724 JET SET floor
is a profoundly cross-linked thermosetting polymer
concrete system that forms a dense hard impermeable
surface upon curing that is resistant to a very wide
range of aggressive chemicals.
BASIC USES
724 JET SET Floor is used:
- as a 3/16"
thick protective floor topping for areas exposed to
aggressive chemicals or areas subjected to high
frequency traffic and concentrated loading.
- to repair or
replace acid brick or ceramic tile.
- to patch
worn or spalled concrete
- to repair
cracks
- to fill
shallow potholes
MAJOR ADVANTAGES
The particular blend
of organic resins used in the manufacture of this product were
selected for their exceptional physical and chemical resistance
characteristics. For example:
- resistance to
most commercially used chemicals
- one hour
cure time at surface temperatures as low as minus 30°C
- complete
ultra-violet stability
- Approved by
Agriculture Canada for incidental food contact
TECHNICAL DATA
| Resin Matrix |
| Compressive
strength |
23,000 psi |
| Tensile strength |
11,000 psi |
| Flexural strength |
17,000 psi |
| Barcol hardness |
45-50 |
| Flash point |
31°C |
| Viscosity at 25°C |
300-650 cps |
| Specific gravity |
1.1-1.2 |
| Net Weight |
1kg/L |
| Solids by volume |
100% |
| Abrasion resistance - weight
loss |
0.9gm |
| Weatherometer - 500 hrs |
no change |
| Water absorption - 72 hrs
immersion |
0.74% |
| Mixed Product |
| Freeze/Thaw 100 cycles |
no change |
| Temp. resistance |
150°C |
| Working time |
20 mins |
| Cure time |
Initial Set |
30 mins |
|
Full Service |
2 hrs |
| Shrinkage on cure |
zero% |
| Application temperature |
-30°C to 30°C |
| Compressive strength |
10,000 psi |
| Flexural strength |
4,000 psi |
| Impact resistance 5mm |
120 in. lbs |
| Abrasion resistance |
C10 no weight
loss |
PRODUCT INFORMATION
| No. of
Components |
Three: Base resin,
Catalyst and Aggregate blend |
| Packaging |
Pre-packaged in proportional batches to
eliminate job site errors. 4L pail Part A complete
with pre-portioned Part B and pre-weighed bag of
Aggregate. 20L pail Part A complete with
pre-portioned units of Part B & 5 pre-weighed
bags of Aggregate. |
| Coverage |
One 4L batch covers
22.5 sq.ft. at a nominal 3/16" thickness. |
| Colours |
Natural, grey, & terra cotta.
Additional colours and colour matches available on
special order. |
| Finish |
Slip resistant,
monolithic. |
| Shelf life |
6 months at 5 to 24°C.
Inside storage, out of sum and away from direct
heat. |
| Application-temperature |
Normal formulation |
10
to 30°C |
|
Low temp
formulation |
-10 to 9°C |
| |
Freezer
formulation |
-30
to -11°C |
|
Specify
application temperature range when ordering. |
All testing to ASTM
Standards by Independent Laboratories.
|
